ShopInstant QuoteFAQDesign GuidesAboutQuote LookupOrder StatusCartMy Account中文Upload a Model · Instant Quote
← Back

DESIGN GUIDELINE

Wall Thickness & Minimum Feature Size Guide

A model that looks fine on screen can print with missing walls, broken pins and blurry text, usually because a feature is smaller than the nozzle can print. Set wall thickness and fine details by this guide and they will come out clean and strong.

01 · SIZE CHART

Minimum size chart

Swipe the table sideways →

FeatureFDM minimumprintableFDM recommendedstrong, reliableResinminimumNotes
Outer walls0.81.2–2.00.6Use multiples of the 0.4 line width: 0.8, 1.2, 1.6, 2.0
Free-standing walls / ribs0.81.20.5Unsupported walls no taller than 10× their thickness
Pins / posts2.03.0+0.8Thin posts break easily and wobble while printing
Holes1.02.0+0.5Holes under 2 mm are best drilled to size after printing
Embossed textstroke 0.6stroke 0.8, 0.6 highstroke 0.3Letter height: FDM ≥ 4 mm, resin ≥ 2 mm
Engraved textstroke 0.6stroke 0.8, 0.6 deepstroke 0.3Text is sharpest on top faces, then side faces
Gap between parts0.30.4–0.50.2Print-in-place moving parts; see the tolerance guide
Unsupported overhang45°under 45°—Angle from vertical; resin is always supported
Unsupported bridge10 mmwithin 5 mm—Horizontal span supported at both ends
Hollow resin parts——wall 2.0, hole 3.5Shell thickness and drain hole diameter when hollowed

Units: mm. FDM values assume a 0.4 mm nozzle. With a 0.2 mm fine nozzle most minimums roughly halve, at the cost of longer print time (pick the nozzle under "Advanced settings" on the quote page).
"Minimum" is the smallest size that prints; strength and finish are not guaranteed. Use the recommended column for load-bearing or long-life parts.

02 · LINE WIDTH

Wall thickness and line width

0.8 mm2 linesRecommended1.0 mm2 lines + gapAvoid1.2 mm3 linesRecommendedWall section: each bead is one extrusion line (0.4 mm)
0.8Exactly 2 lines: the thinnest practical wall, fine for enclosures that carry no load.
1.0Not a multiple of the line width: leaves a gap or needs filler lines, weaker and rougher.
1.2+3 lines or more (1.2, 1.6, 2.0) are strongest; use these for most parts.

03 · RULES

Four basic rules

  1. Use multiples of the line width: 0.8, 1.2, 1.6, 2.0 mm; avoid 1.0 or 1.4, which leave gaps.
  2. Keep walls even: Keep thick and thin sections within 2× of each other. Sudden thick sections cool unevenly and warp or sink.
  3. No need for solid: Thick sections are filled with infill; set walls and infill under "Advanced settings" on the quote page. Solid parts are heavier, cost more and warp more.
  4. Stiffen thin walls with ribs: Add ribs 0.5–0.8× the wall thickness and no taller than 3× the wall. Lighter and stiffer than thickening the whole wall.

04 · DESIGN TIPS

Design tips

Text and logos

  • Text is sharpest on top faces; downward faces carry support marks.
  • Thin strokes in serif fonts disappear; use a bold sans-serif.
  • Embossed text prints more easily; engraved text wears better.

Thin pins and small holes

  • Tall thin pins (over 5× their diameter) wobble while printing; thicken them, fillet or add ribs at the base.
  • Holes under 2 mm close up or shrink; drill them to size if they must be accurate.
  • For pin and screw holes see the screw hole guide.

Large flat areas and warping

  • Large flat plates lift at the edges; add ribs, round the corners and avoid big flat ABS plates.
  • Long thin parts lift at both ends; give the long edge some height or split it.
  • If a flat face must sit flush against another part, say so in the notes.

Overhangs and supports

  • Overhangs past 45° and long bridges need supports, which add cost and leave marks.
  • Turning an overhang into a 45° slope or chamfer often removes the need for supports.
  • On the quote page you can choose the orientation and preview the one with the least support.

05 · MATERIALS

Material notes

GoodPLA / PLA+Sharpest detail; the minimums apply. Good for small text and thin ribs.
GoodPETGStrings slightly; use the recommended column for strokes and gaps.
CautionABS / ASAShrinks more, so thin walls and large plates warp; use 1.6 mm or more for outer walls.
CautionTPUSoft; walls at least 1.2 mm. Thin pins and small text are hard to print well.
CautionPA-CF / carbon fibreNeeds a larger nozzle; walls and strokes at least 1.2 mm.
GoodResinFinest detail, down to 0.3 mm strokes. Hollow large parts and add drain holes.

06 · CHECKLIST

Pre-submission checklist

Not sure a detail will print? Send it to us

Share your file or a screenshot and we will check walls, text and fine details, and suggest a material and orientation.

Contact us on LINE Download PDF Guide