ShopInstant QuoteFAQDesign GuidesAboutQuote LookupOrder StatusCartMy Account中文Upload a Model · Instant Quote
← Back

DESIGN GUIDELINE

Tolerance & Fit Clearance Design Guide

When two printed parts slide together, plug in or rotate, too little clearance and they will not assemble, too much and they rattle. Model the clearance into your parts by use case and they go together straight off the printer.

01 · FIT CHART

Clearance chart

Swipe the table sideways →

FitGap per side cFDMHole − shaftFDMGap per side cResinTypical use
Press fitpermanent0–0.050–0.10Pins and sleeves pressed in for good; will not work loose
Snug fitpush by hand0.10.20.05Goes in by hand with no play; locating pins, lids
Sliding0.15–0.20.3–0.40.1Drawers, rails, removable inserts
Rotating0.250.50.15Hinge pins, knobs, wheels
Loose0.3–0.40.6–0.80.2Easy assembly with a little play; enclosure slots
Print-in-placemoving parts0.4–0.5—0.3Moves straight off the printer; hinges, chain links

Units: mm. FDM values assume a 0.4 mm nozzle, 0.2 mm layers and PLA; "hole − shaft" = 2 × gap per side. The values already include normal print error: with holes and shafts printed axis-up, model them at the sizes in the chart. Add another 0.1 mm for horizontal holes.
Materials, colours and machines vary slightly. For tight fits or larger batches, print a short test piece first.

02 · CROSS SECTION

Clearance diagram

Hole = shaft + 2cShaft ØccPart (section)Shaft / insert
cGap per side: the space between the hole wall and the shaft on one side. Pick it from the chart by fit type.
HoleHole = shaft + 2c. Example: an Ø8 shaft that should slide gets an Ø8.3–8.4 hole.
ShaftYou can shrink the shaft instead. When both parts are printed, count the clearance once: do not enlarge the hole and shrink the shaft as well.

03 · ACCURACY

General accuracy

Swipe the table sideways →

FeatureFDMPLA / PETG / ABSResinSLA / LCD
General dimensions±0.2 mm or ±0.2% (whichever is larger)±0.1 mm or ±0.15%
Vertical holes (axis up)About 0.1–0.2 mm undersizeAbout 0.05–0.1 mm undersize
Horizontal holesTop sags, about 0.2–0.3 mm undersizeAbout 0.1 mm undersize
First layerSpreads 0.1–0.3 mm (elephant foot)Support contact areas need sanding
Height (Z)±1 layer height±0.05 mm
Large ABS / ASA partsShrinks 0.5–0.8% as it cools—

Typical values for ordinary parts, not guarantees: shape, size, material and orientation all affect accuracy. If specific dimensions matter, list them in the order notes and we will orient and tune the print around them.

04 · DESIGN TIPS

Design tips

Print orientation

  • Holes and shafts printed axis-up (perpendicular to the bed) come out roundest and most accurate.
  • Shafts printed lying down come out slightly flattened; add another 0.1 mm of clearance.
  • Keep mating faces in the same orientation relative to the bed so errors match.

Chamfers and elephant foot

  • Add a 0.5 mm chamfer to hole entries and shaft ends for easy alignment.
  • A 0.3–0.5 mm chamfer on bottom edges cancels the first-layer spread (elephant foot).
  • If the bottom face must sit flush against another part, say so in the notes.

Long and multi-point fits

  • For fits longer than 3× the diameter, relieve the middle by 0.1–0.2 mm so only the ends locate; it will not bind.
  • When several pins must line up with several holes, use a sliding fit on the holes to absorb position error.

Print a test piece

  • For tight fits or larger batches, print a short test piece with only the mating features.
  • Use the same material and orientation as the real part.
  • Bearings, magnets and screws have their own guides: bearing housings, magnets, screw holes.

05 · MATERIALS

Material notes

GoodPLA / PLA+Most dimensionally stable with little shrinkage; use the chart as is.
GoodPETGSlightly sticky surface and light stringing; add 0.05 mm to sliding and rotating fits.
GoodABS / ASAShrinks more as it cools; hole spacing on parts over 100 mm comes out 0.5–0.8% small. Print mating parts together, in the same orientation.
GoodPA / PA-CFSwells slightly as it absorbs moisture; add 0.05 mm. Carbon fibre leaves a rougher surface, so sliding parts run tighter.
CautionTPUToo soft for sliding or rotating fits. To clamp, use negative clearance (shaft 0.1–0.2 mm larger than the hole).
GoodResinHighest accuracy; use the resin column. The material is brittle, so do not make press fits too tight or the part may crack.

06 · CHECKLIST

Pre-submission checklist

Not sure about a fit? Send it to us

Share your file or a screenshot and tell us which parts assemble, slide or stay fixed. We will check the clearances for you.

Contact us on LINE Download PDF Guide