ShopInstant QuoteFAQDesign GuidesAboutQuote LookupOrder StatusCartMy Account中文Upload a Model · Instant Quote
← Back

DESIGN GUIDELINE

Magnet Embedding Design Guide

Embed disc magnets in 3D-printed parts for magnetic lids, storage boxes and detachable modules. Model the pockets to this guide so the magnets fit, stay put and do not crack the part.

01 · SIZE CHART

Size chart

Swipe the table →

Magnet dia.DThicknessTPress-fit holetightGlue-in holeD + 0.3Open pocket depthT + 0.1Print-in pocketdia. × depthMin. walltMagnet spacingmin. p (center)
Ø42 thicknesses14.14.31.14.3 × 1.21.27
24.14.32.14.3 × 2.21.27
Ø52 thicknesses15.15.31.15.3 × 1.21.28
25.15.32.15.3 × 2.21.28
Ø62 thicknesses16.156.31.16.3 × 1.21.29
26.156.32.16.3 × 2.21.29
Ø82 thicknesses18.158.31.18.3 × 1.21.511
28.158.32.18.3 × 2.21.511
Ø125 thicknesses112.212.31.112.3 × 1.2215
212.212.32.112.3 × 2.2215
312.212.33.112.3 × 3.2215
412.212.34.112.3 × 4.2215
512.212.35.112.3 × 5.2215
Ø155 thicknesses115.215.31.115.3 × 1.22.518
215.215.32.115.3 × 2.22.518
315.215.33.115.3 × 3.22.518
415.215.34.115.3 × 4.22.518
515.215.35.115.3 × 5.22.518
Ø185 thicknesses118.218.31.118.3 × 1.22.521
218.218.32.118.3 × 2.22.521
318.218.33.118.3 × 3.22.521
418.218.34.118.3 × 4.22.521
518.218.35.118.3 × 5.22.521

Unit: mm. The chart covers the NdFeB disc magnets we sell (same sizes as in our shop). Model the holes with these values directly; no shrinkage compensation needed. Tolerances vary between printers and materials, so print a test hole first for larger runs.
Press-fit holes are tight: push the magnet in straight with a flat tool. If you want easy insertion and glue afterwards, use the glue-in size.

02 · CROSS SECTION

Cross section

Magnet ØD H t (≥ min. wall) Open pocket (press / glue) Part surface Magnet Cover ≥ 0.6 mm C Print-in (closed)
ØDHole diameter: use the press-fit size (tight) or the glue-in size (D + 0.3, room for glue).
HOpen pocket depth: magnet thickness + 0.1 mm so it sits flush. Tell us if you want it proud or recessed.
CPrint-in: pause the print at the top of the pocket, drop the magnet in and resume. Pocket D + 0.3, depth T + 0.2, with at least 0.6 mm (about 3 layers) on top.
tWall: solid material from the pocket to the outer edge. Too thin and it bulges or cracks.

03 · METHODS

Embedding methods

  1. Press-fit: Fastest, no glue; the magnet is flush with the surface. Best for rigid materials such as PLA and PETG.
  2. Glue-in: Looser hole, fixed with epoxy or CA glue. Works with any material and can be done later.
  3. Print-in: Pause the print, drop the magnet in, resume. Fully enclosed and invisible, cannot fall out, but the pull is weaker than an exposed magnet.

04 · DESIGN TIPS

Design tips

Polarity

  • When two parts should attract each other, mark which face points out and which parts pair up, e.g. "part A: N out, part B: S out".
  • Multiple magnets in one part should all face the same way unless your drawing says otherwise; a wrong one will repel.
  • If polarity does not matter (e.g. sticking to steel), let us know.

Pocket shape

  • Use a flat-bottomed straight hole, no taper. A 0.2–0.3 mm chamfer at the opening helps alignment.
  • For press-fit, 3–4 small vertical grooves (0.3 mm) in the wall let air escape.
  • Print pockets facing up (axis perpendicular to the bed) for the roundest, most accurate holes.

Pull force & distance

  • Magnetic force drops quickly with distance: keep print-in covers thin (0.6–1 mm).
  • For a stronger hold, use a thicker magnet or leave it exposed so the magnets touch directly.
  • Magnets placed too close attract each other or flip; keep the spacing in the chart.

Cautions

  • NdFeB magnets lose magnetism permanently above about 80 °C: never heat-set them, and keep them away from heat.
  • Magnets are brittle and chip if they snap together. Keep small magnets away from children.
  • Keep them away from phones, credit cards and mechanical watches.

05 · MATERIALS

Materials

GoodPLA / PLA+Most common; press-fit or glue-in. For parts kept above 50 °C, use PETG or better.
GoodPETGTough and less likely to crack, ideal for press-fit.
GoodABS / ASA / PCHeat-resistant; press-fit or glue-in.
GoodResin (SLA)Resin parts are brittle: use the glue-in size, not press-fit.
CautionTPU (flexible)Too soft to hold a magnet by friction: glue it in or embed it during printing.

06 · CHECKLIST

Checklist before sending

Not sure about your design? Send it to us

Share your file or a screenshot and we will check the pockets and magnet sizes. We can also embed the magnets when we print your parts; just mention it when you request a quote.

Contact us on LINE Download PDF Guide