ShopInstant QuoteFAQDesign GuidesAboutQuote LookupOrder StatusCartMy Account中文Upload a Model · Instant Quote
← Back

DESIGN GUIDELINE

Snap-Fit Design Guide

Snap-fits click together without screws, ideal for enclosures and lids. Make the hook too tall and the arm breaks, too short and it will not hold. Look up the hook height from arm thickness and length, print the arm lying flat, and it will snap together again and again.

01 · SIZE CHART

Cantilever snap-fit chart

Swipe the table sideways →

Thickness tat rootLength LL / tMax hook height yPLAMax hook height yPETG / ABS / ASAMax hook height yPA nylon
1.286.70.30.60.8
1.21210.00.81.41.9
1.6127.50.61.01.4
1.61610.01.11.82.6
2.0168.00.91.52.1
2.02010.01.42.33.2
2.42410.01.62.83.9

Units: mm. Calculated for a uniform rectangular cantilever: y = 0.67 × ε × L² ÷ t, with allowable strain ε of 1.5% for PLA, 2.5% for PETG / ABS / ASA and 3.5% for nylon. The values already include a 0.7 safety factor.
Arm width does not change the hook height; make it at least 4 mm. Wider arms snap tighter and are harder to press. Keep L / t between 6 and 10: shorter arms break, longer ones hold loosely. Use the formula for sizes not in the chart.

02 · CROSS SECTION

Snap-fit diagram

RLty90°30°Catch on the mating partPart bodyPrint the arm lying flat, layers running along its lengthPush
LArm length from the root to the hook's return face. Longer arms are easier to press and less likely to break.
tArm thickness at the root; at least 1.2 mm (3 lines).
yHook height that catches the mating part; keep it within the chart.
RRoot fillet R ≥ 0.5t, at least 0.5 mm. Sharp roots are where arms break.
AngleA 30° lead-in presses in easily. A 90° return face locks for good; 45° can be pulled apart by hand.

03 · TYPES

Common snap-fit types

  1. Cantilever: The most common: a flexible arm with a hook. Enclosures, battery covers, panels. Size it from the chart.
  2. Annular: A full ring lip on round lids and caps. Lip height 0.3–0.5 mm; slot the lid wall in 2–4 places so it can open up.
  3. Torsion / U-shaped: A U-shaped arm or a torsion bar spreads the strain; good for features opened often.
  4. Tab and slot: No flexing: the tab slides in and locates with a little interference. Use the snug fit from Tolerances & fit clearance.

04 · DESIGN TIPS

Design tips

Orientation matters most

  • The arm must lie flat on the bed, with layers running along its length.
  • Printed upright, the arm is weakest between layers and snaps off at a layer line.
  • If the part cannot be oriented that way, make the snap a separate part and assemble it.

Root and tapered arms

  • Fillet the root at R ≥ 0.5t to avoid a stress concentration.
  • Tapering the arm to half thickness at the tip lets it flex about 1.6× further without breaking.
  • Do not put the root on the thinnest section of the part.

Clearance and removal

  • Leave 0.2–0.3 mm per side between the hook and the catch for easy alignment.
  • For snaps that must come apart, use a 45° return face or a notch for a flat screwdriver.
  • Leave room around the arm to flex (at least y + 0.5 mm).

Count and placement

  • Use 2–4 snaps per lid, placed symmetrically.
  • Add locating ribs or pins: snaps hold, ribs align.
  • For features opened hundreds of times, use screws or heat-set inserts instead.

05 · MATERIALS

Materials

GoodPETGTough and the top recommendation; survives repeated opening.
GoodABS / ASATough and heat resistant; good for enclosures.
GoodPA nylonBest for repeated flexing; allows taller hooks.
CautionPLA / PLA+Stiff and brittle; only for snaps that are rarely opened. Use the PLA column.
CautionCarbon-fibre compositesFibre makes the material stiffer and more brittle; use the PLA column.
CautionResinStandard resin is brittle and not recommended for snaps. Tough resin may work; ask us first.
CautionTPUAlready flexible, so it needs no snap features; use an interference fit.

06 · CHECKLIST

Pre-submission checklist

Worried a snap will break? Send it to us

Share your file or a screenshot and we will check the hook height, material and print orientation.

Contact us on LINE Download PDF Guide